View MIC501405_4198713.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MIC5014/5015
Micrel, Inc.
MIC5014/5015
Low-Cost High- or Low-Side MOSFET Driver
General Description
MIC5014 and MIC5015 MOSFET drivers are designed for gate control of N-channel, enhancement-mode, power MOSFETs used as high-side or low-side switches. The MIC5014/5 can sustain an on-state output indefinitely. The MIC5014/5 operates from a 2.75V to 30V supply. In highside configurations, the driver can control MOSFETs that switch loads of up to 30V. In low-side configurations, with separate supplies, the maximum switched voltage is limited only by the MOSFET. The MIC5014/5 has a TTL compatible control input. The MIC5014 is noninverting while the MIC5015 is inverting. The MIC5014/5 features an internal charge pump that can sustain a gate voltage greater than the available supply voltage. The driver is capable of turning on a logic-level MOSFET from a 2.75V supply or a standard MOSFET from a 5V supply. The gate-to-source output voltage is internally limited to approximately 15V. The MIC5014/5 is protected against automotive load dump, reversed battery, and inductive load spikes of -20V. The driver's overvoltage shutdown feature turns off the external MOSFET at approximately 35V to protect the load against power supply excursions. The MIC5014 is an improved pin-for-pin compatible replacement in many MIC5011 applications. The MIC5014/5 is available in plastic 8-pin DIP and 8-pin SOIC pacakges.
Features
* * * * * * * * * * * * * * 2.75V to 30V operation 100A maximum supply current (5V supply) 15A typical off-state current Internal charge pump TTL compatible input Withstands 60V transient (load dump) Reverse battery protected to -20V Inductive spike protected to -20V Overvoltage shutdown at 35V Internal 15V gate protection Minimum external parts Operates in high-side or low-side configurations 1A control input pull-off Inverting and noninverting versions
Applications
* * * * * * Automotive electrical load control Battery-powered computer power management Lamp control Heater control Motor control Power bus switching
Typical Application
+3V to +4V 10F MIC5014 1 Control Input
ON OFF
V+ Input
NC NC
8 7
2 3
Source 4 Gnd
6 NC Gate 5
IRLZ24
Figure 1. 3V "Sleep-Mode" Switch with a Logic-Level MOSFET
Micrel, Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel + 1 (408) 944-0800 * fax + 1 (408) 474-1000 * http://www.micrel.com
June 2005
Load
1
MIC5014/5015
MIC5014/5015
Micrel, Inc.
Ordering Information
Part Number Standard Pb-Free MIC5014BM MIC5014BN MIC5015BM MIC5015BN MIC5014YM MIC5014YN MIC5015YM MIC5015YN Temperature Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C Configuration Non-Inverting Non-Inverting Inverting Inverting Package 8-Pin SOIC 8-Pin PDIP 8-Pin SOIC 8-Pin PDIP
Block Diagram
V+ (1)
Charge Pump
Gate (5)
15V
Source (3) Input (2) *
* Only on the inverting version
Ground (4)
Pin Description
Pin Number 1 2 3 Pin Name V+ Input Source Pin Function Supply. Must be decoupled to isolate from large transients caused by the power MOSFET drain. 10F is recommended close to pins 1 and 4. Turns on power MOSFET when taken above (or below) threshold (1.0V typical). Pin 2 requires ~ 1A to switch. Connects to source lead of power MOSFET and is the return for the gate clamp zener. Pin 3 can safely swing to -20V when turning off inductive loads.
4 5 6, 7, 8
MIC5014/5015
Ground Gate NC Drives and clamps the gate of the power MOSFET. Not internally connected.
2
June 2005
MIC5014/5015
Micrel, Inc.
Absolute Maximum Ratings (Notes 1,2)
Supply Voltage ............................................... -20V to 60V Input Voltage ..................................................... -20V to V+ Source Voltage ..................................................-20V to V+ Source Current .......................................................... 50mA Gate Voltage .................................................. -20V to 50V Junction Temperature .............................................. 150C
Operating Ratings (Notes 1,2)
JA (Plastic DIP) ..................................................... 160C/W JA (SOIC) ............................................................. 170C/W Ambient Temperature: ................................ -40C to +85C Storage Temperature ................................ -65C to +150C Lead Temperature ...................................................... 260C (max soldering time: 10 seconds) Supply Voltage (V+) ......................................... 2.75V to 30V
Electrical Characteristics (Note 3) TA = -40C to +85C
Parameter Supply Current V+ = 30V V+ = 5V V+ = 3V Logic Input Voltage Threshold VIN Logic Input Current MIC5014 (non-inverting) Logic Input Current MIC5015 (inverting) Input Capacitance Gate Enhancement VGATE - VSUPPLY Zener Clamp VGATE - VSOURCE Gate Turn-on Time, tON (Note 4) 3.0V V+ 30V TA = 25C 3.0V V+ 30V 3.0V V+ 30V
3.0V V+ 30V 8.0V V+ 30V V+ = 4.5V CL = 1000pF V+ = 12V CL = 1000pF V+ = 4.5V CL = 1000pF V+ = 12V CL = 1000pF
unless otherwise specified Conditions Min Typ VIN De-Asserted (Note 5) 10 VIN Asserted (Note 5) 5.0 VIN De-Asserted 10 VIN Asserted 60 VIN De-Asserted 10 VIN Asserted 25 Digital Low Level Digital High Level 2.0 VIN Low -2.0 0 VIN High 1.0 VIN Low -2.0 -1.0 VIN High -1.0 5.0 VIN Asserted 4.0 VIN Asserted 13 15 2.5 90 6.0 6.0 35 37
Max 25 10 25 100 25 35 0.8
Units A mA A A V A A pF V V ms s s s V
2.0 2.0 17 17 8.0 140 30 30 41
Gate Turn-off Time, tOFF (Note 4)
VIN switched on, measure time for VGATE to reach V+ + 4V As above, measure time for VGATE to reach V+ + 4V VIN switched off, measure time for VGATE to reach 1V As above, measure time for VGATE to reach 1V
Overvoltage Shutdown Threshold
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when operating the device beyond its specified Operating Ratings. Note 2: The MIC5014/5015 is ESD sensitive. Note 3: Minimum and maximum Electrical Characteristics are 100% tested at TA = 25C and TA = 85C, and 100% guaranteed over the entire operating temperature range. Typicals are characterized at 25C and represent the most likely parametric norm. Note 4: Test conditions reflect worst case high-side driver performance. Low-side and bootstrapped topologies are significantly faster--see Applications Information. Note 5: "Asserted" refers to a logic high on the MIC5014 and a logic low on the MIC5015.
June 2005
3
MIC5014/5015
MIC5014/5015
Micrel, Inc.
Typical Characteristics All data measured using FET probe to minimize resistive loading
Supply Current (Output Asserted)
6
GATE ENHANCEMENT (V)
Gate Enhancement vs. Supply Voltage
20
TURN-ON TIME (s)
300 250 200 150 100 50 0 0
High-Side Turn-On Time vs. Gate Capacitance
SUPPLY CURRENT (mA)
5 4 3 2 1 0 0 5 10 15 20 25 SUPPLY VOLTAGE (V) 30
15
10
5 Gate Enhancement = VGATE - VSUPPLY 0 0 5 10 15 20 25 SUPPLY VOLTAGE (V) 30
Supply = 12V 2 4 6 8 10 GATE CAPACITANCE (nF)
High-Side Turn-On Time Until Gate = Supply + 4V
100 TURN-ON TIME (ms)
TURN-ON TIME (ms)
High-Side Turn-On Time Until Gate = Supply + 4V
HIGH-SIDE TURN-ON TIME (s)
High-Side Turn-On Time vs. Temperature
180 160 140 120 100 80 60 40 20 0 -60 -30 0 30 60 90 120 150 AMBIENT TEMPERATURE (C) Supply = 12V CGATE = 1000pF
100 CGATE = 1300pF CGATE = 3000pF
10
10
1
1
0.1
0.1
0.01
0
4 8 12 16 20 24 SUPPLY VOLTAGE (V)
28
0.01
0
4 8 12 16 20 24 SUPPLY VOLTAGE (V)
28
High-Side Turn-On Time Until Gate = Supply + 10V
100 100 CGATE = 1300pF
High-Side Turn-On Time Until Gate = Supply + 10V
10 TURN-OFF TIME (s) CGATE = 3000pF 8 6
High-Side Turn-Off Time Until Gate = 1V
TURN-ON TIME (ms)
10
TURN-ON TIME (ms)
10
1
1
CGATE = 3000pF 4 2 0 CGATE = 1300pF 0 5 10 15 20 25 SUPPLY VOLTAGE (V) 30
0.1
0.1
0.01
0
5 10 15 20 25 SUPPLY VOLTAGE (V)
30
0.01
0
5 10 15 20 25 SUPPLY VOLTAGE (V)
30
Charge-Pump Output Current
1000 10000 OUTPUT CURRENT (A) 28V 100
Charge-Pump Output Current
10000 28V 1000 12V Source connected to ground: supply voltage as noted 5V 3V TURN-ON TIME (s)
Low-Side Turn-On Time Until Gate = 4V
CGATE = 3000pF 1000
OUTPUT CURRENT (A)
12V
100
100 CGATE = 1300pF
10 5V 3V
Source connected to supply: supply voltage as noted
10
10
1
0 5 10 15 GATE-TO-SOURCE VOLTAGE (V)
1
0 5 10 15 GATE-TO-SOURCE VOLTAGE (V)
1
0
5 10 15 20 25 SUPPLY VOLTAGE (V)
30
MIC5014/5015
4
June 2005
MIC5014/5015
Micrel, Inc. not use a socket for the MOSFET. If the MOSFET is a TO-220 type package, make high current connections to the drain tab. Wiring losses have a profound effect on high-current circuits. A floating milliohmeter can identify connections that are contributing excess drop under load. Low Voltage Testing As the MIC5014/MIC5015 have relatively high output impedances, a normal oscilloscope probe will load the device. This is especially pronounced at low voltage operation. It is recommended that a FET probe or unity gain buffer be used for all testing.
Applications Information
Functional Description
The MIC5014 is functionally and pin for pin compatible with the MIC5011, except for the omission of the optional speedup capacitor pins, which are available on the MIC5011. The MIC5015 is an inverting configuration of the MIC5014. The internal functions of these devices are controlled via a logic block (refer to block diagram) connected to the control input (pin 2). When the input is off (low for the MIC5014, and high for the MIC5015), all functions are turned off, and the gate of the external power MOSFET is held low via two Nchannel switches. This results in a very low standby current; 15A typical, which is necessary to power an internal bandgap. When the input is driven to the "ON" state, the N-channel switches are turned off, the charge pump is turned on, and the P-channel switch between the charge pump and the gate turns on, allowing the gate of the power FET to be charged. The op amp and internal zener form an active regulator which shuts off the charge pump when the gate voltage is high enough. This is a feature not found on the MIC5011. The charge pump incorporates a 100kHz oscillator and onchip pump capacitors capable of charging a 1,000pF load in 90s typical. In addition to providing active regulation, the internal 15V zener is included to prevent exceeding the VGS rating of the power MOSFET at high supply voltages. The MIC5014/15 devices have been improved for greater ruggedness and durability. All pins can withstand being pulled 20V below ground without sustaining damage, and the supply pin can withstand an overvoltage transient of 60V for 1s. An overvoltage shutdown has also been included, which turns off the device when the supply exceeds 35V.
Circuit Topologies
The MIC5014 and MIC5015 are well suited for use with standard power MOSFETs in both low and high side driver configurations. In addition, the lowered supply voltage requirements of these devices make them ideal for use with logic level FETs in high side applications with a supply voltage of 3 to 4V. (If higher supply voltages [>4V] are used with logic level FETs, an external zener clamp must be supplied to ensure that the maximum VGS rating of the logic FET [10V] is not exceeded.) In addition, a standard IGBT can be driven using these devices. Choice of one topology over another is usually based on speed vs. safety. The fastest topology is the low side driver, however, it is not usually considered as safe as high side driving as it is easier to accidentally short a load to ground than to VCC. The slowest, but safest topology is the high side driver; with speed being inversely proportional to supply voltage. It is the preferred topology for most military and automotive applications. Speed can be improved considerably by bootstrapping from the supply. All topologies implemented using these devices are well suited to driving inductive loads, as either the gate or the source pin can be pulled 20V below ground with no effect. External clamp diodes are unnecessary, except for the case in which a transient may exceed the overvoltage trip point. High Side Driver (Figure 1) The high side topology shown here is an implementation of a "sleep-mode" switch for a laptop or notebook computer which uses a logic level FET. A standard power FET can easily be substituted when supply voltages above 4V are required.
+3V to +30V
Construction Hints
High current pulse circuits demand equipment and assembly techniques that are more stringent than normal, low current lab practices. The following are the sources of pitfalls most often encountered during prototyping: Supplies : Many bench power supplies have poor transient response. Circuits that are being pulse tested, or those that operate by pulse-width modulation will produce strange results when used with a supply that has poor ripple rejection, or a peaked transient response. Always monitor the power supply voltage that appears at the drain of a high side driver (or the supply side of the load for a low side driver) with an oscilloscope. It is not uncommon to find bench power supplies in the 1kW class that overshoot or undershoot by as much as 50% when pulse loaded. Not only will the load current and voltage measurements be affected, but it is possible to overstress various components, especially electrolytic capacitors, with possibly catastrophic results. A 10F supply bypass capacitor at the chip is recommended. Residual resistances: Resistances in circuit connections may also cause confusing results. For example, a circuit may employ a 50m power MOSFET for low voltage drop, but unless careful construction techniques are used, one could easily add 50 to 100m resistance. Do
10F MIC5014 V+ Input NC NC NC Control Input
ON OFF
2 3
7 6
Source 4 Gnd
Gate 5
Figure 2. Low Side Driver
June 2005
5
Load
1
8
MIC5014/5015
MIC5014/5015 Low Side Driver (Figure 2) A key advantage of this topology, as previously mentioned, is speed. The MOSFET gate is driven to near supply immediately when the MIC5014/15 is turned on. Typical circuits reach full enhancement in 50s or less with a 15V supply. Bootstrapped High Side Driver (Figure 3) The turn-on time of a high side driver can be improved to faster than 40s by bootstrapping the supply with the MOSFET source. The Schottky barrier diode prevents the supply pin from dropping more than 200mV below the drain supply and improves turnon time. Since the supply current in the "off" state is only a small leakage, the 100nF bypass capacitor tends to remain charged for several seconds after the MIC5014/15 is turned off. Faster speeds can be obtained at the expense of supply voltage (the overvoltage shutdown will turn the part off when the bootstrapping action pulls the supply pin above 35V) by using a larger capacitor at the junction of the two 1N4001 diodes. In a PWM application (this circuit can be used for either PWM'ed or continuously energized loads), the chip supply is sustained at a higher potential than the system supply, which improves switching time.
+2.75V to +30V 1N5817
Micrel, Inc. the short is removed, feedback to the input pin insures that the MIC5014 will turn back on. This output can also be level shifted and sent to an I/O port of a microcontroller for intelligent control. Current Shunts (RS). Low valued resistors are necessary for use at RS. Resistors are available with values ranging from 1 to 50m, at 2 to 10W. If a precise overcurrent trip point is not necessary, then a nonprecision resistor or even a measured PCB trace can serve as RS. The major cause of drift in resistor values with such resistors is temperature coefficient; the designer should be aware that a linear, 500 ppm/C change will contribute as much as 10% shift in the overcurrent trip point. If this is not acceptable, a power resistor designed for current shunt service (drifts less than 100 ppm/C), or a Kelvin-sensed resistor may be used.
12V
On ITRIP = VTRIP/RS = 1.7A VTRIP = R1/(R1+R2) MIC5014 1 2 V+ Input Source NC NC NC 8 7 6 R4 1k RS 0.06 R1 1k
10F
1N4001 (2) 100nF 1F MIC5015 V+ Input Source NC NC NC Control Input
ON OFF
3
4 Gnd
Gate 5
2 3
7 6 1RF540
4 Gnd
Gate 5
Figure 4. High Side Driver with Overcurrent Shutdown
Suppliers of Precision Power Resistors: Dale Electronics, Inc., 2064 12th Ave., Columbus, NE 68601. (402) 5653131 International Resistive Co., P.O. Box 1860, Boone,NC 28607-1860. (704) 264-8861 Isotek Corp., 566 Wilbur Ave. Swansea, MA 02777. (508) 673-2900 Kelvin, 14724 Ventura Blvd., Ste. 1003, Sherman Oaks, CA 91403-3501. (818) 990-1192 RCD Components, Inc., 520 E. Industrial Pk. Dr., Manchester, NH 03103. (603) 669-0054 Ultronix, Inc., P.O. Box 1090, Grand Junction, CO 81502 (303) 242-0810
Load
Figure 3. Bootstrapped Hgh-Side Driver High Side Driver With Current Sense (Figure 4) Although no current sense function is included on the MIC5014/15 devices, a simple current sense function can be realized via the addition of one more active component; an LM301A op amp used as a comparator. The positive rail of the op amp is tied to V+, and the negative rail is tied to ground. This op amp was chosen as it can withstand having input transients that swing below the negative rail, and has common mode range almost to the positive rail. The inverting side of this comparator is tied to a voltage divider which sets the voltage to V+ - VTRIP . The non inverting side is tied to the node between the drain of the FET and the sense resistor. If the overcurrent trip point is not exceeded , this node will always be pulled above V+ - VTRIP, and the output of the comparator will be high which feeds the control input of the MIC5014 (polarities should be reversed if the MIC5015 is used). One the overcurrent trip point has been reached, the comparator will go low, which shuts off the MIC5014. When the
MIC5014/5015
High Side Driver With Delayed Current Sense (Figure 5) Delay of the overcurrent detection to accomodate high inrush loads such as incandescent or halogen lamps can be accomplished by adding an LM3905 timer as a one shot to provide an open collector pulldown for the comparator output such that the control input of the MIC5015 stays low for a preset amount of time without interference from the current sense circuitry. Note that an MIC5015 must be used in this application (figure 5), as an inverting control input is necessary. The delay time is set by the RC time constant of the external components on pins 3 and 4 of the timer; in this case, 6ms was chosen. An LM3905 timer was used instead of a 555 as it provides a clean transition, and is almost impossible to make oscillate. Good bypassing and noise immunity is essential in this circuit to prevent spurious op amp oscillations. 6 June 2005
Load
1
8
LM301A R2 120k 2.2k
MIC5014/5015
Micrel, Inc.
12V
12V 1 On 2 3 10F MIC5014 1 2 3 V+ Input Source NC NC NC 8 7 6 R4 1k RS 0.06 R1 1k 1000pF 0.01F
LM3905N Trigger Logic VREF R/C Emit Coll 8 7 6
4 Gnd
V+ 5
4 Gnd
Gate 5
Load
R2 LM301A 120k
2.2k
1k
Figure 5. High Side Driver with Delayed Overcurrent Shutdown
Typical Applications
Variable Supply Low Side Driver for Motor Speed Control (Figure 6) The internal regulation in the MIC5014/15 allows a steady gate enhancement to be supplied while the MIC5014/15 supply varies from 5V to 30V, without damaging the internal gate to source zener clamp. This allows the speed of the DC motor shown to be varied by varying the supply voltage.
VCC = +5V to +30V
MIC5014 1
ON OFF
V+ Input Source
NC NC NC
8 7 6 IRF540 M
2 3
applications, it is acceptable to allow this voltage to momentarily turn the MOSFET back on as a way of dissipating the inductor's current. However, if this occurs when driving a solenoid valve with a fast switching speed, chemicals or gases may be inadvertantly be dispensed at the wrong time with possibly disasterous consequences. Also, too large of a kickback voltage (as is found in larger solenoids) can damage the MIC5014 or the power FET by forcing the Source node below ground (the MIC5014 can be driven up to 20V below ground before this happens). A catch diode has been included in this design to provide an alternate route for the inductive kickback current to flow. The 5k resistor in series with this diode has been included to set the recovery time of the solenoid valve.
24V
4 Gnd
Gate 5
MIC5015 1
OFF ON
V+ Input Source
NC NC NC
8 7 6 IRFZ40
2 3
4 Gnd
Gate 5
Figure 6: DC Motor Speed Control/Driver Solenoid Valve Driver (Figure 7) High power solenoid valves are used in many industrial applications requiring the timed dispensing of chemicals or gases. When the solenoid is activated, the valve opens (or closes), releasing (or stopping) fluid flow. A solenoid valve, like all inductive loads, has a considerable "kickback" voltage when turned off, as current cannot change instantaneously through an inductor. In most June 2005 7
ASCO 8320A Solenoid
1N4005 5k
Figure 7: Solenoid Valve Driver
MIC5014/5015
MIC5014/5015 Incandescent/Halogen Lamp Driver (Figure 8) The combination of an MIC5014/5015 and a power FET makes an effective driver for a standard incandescent or halogen lamp load. Such loads often have high inrush currents, as the resistance of a cold filament is less than one-tenth as much as when it is hot. Power MOSFETs are well suited to this application as they have wider safe operating areas than do power bipolar transistors. It is important to check the SOA curve on the data sheet of the power FET to be used against the estimated or measured inrush current of the lamp in question prior to prototyping to prevent "explosive" results. If overcurrent sense is to be used, first measure the duration of the inrush, then use the topology of Figure 5 with the RC of the timer chosen to accomodate the duration with suitable guardbanding.
12V 330k 10F MIC5014 1 Control Input
ON OFF
Micrel, Inc. Motor Driver With Stall Shutdown (Figure 10) Tachometer feedback can be used to shut down a motor driver circuit when a stall condition occurs. The control switch is a 3-way type; the "START" position is momentary and forces the driver ON. When released, the switch returns to the "RUN" position, and the tachometer's output is used to hold the MIC5014 input ON. If the motor slows down, the tach output is reduced, and the MIC5014 switches OFF. Resistor "R" sets the shutdown threshold.
12V
10F MIC5014 1 2 3 V+ Input Source NC NC NC 8 7 6 IRFZ44
4 Gnd V+ Input Source NC NC NC 8 7 6 IRF540 1N4148 T R 330k
Gate 5
2 3
4 Gnd
Gate 5
M
OSRAM HLX64623
Figure 10. Motor Stall Shutdowm
Figure 8. Halogen Lamp Driver Relay Driver (Figure 9) Some power relay applications require the use of a separate switch or drive control, such as in the case of microprocessor control of banks of relays where a logic level control signal is used, or for drive of relays with high power requirements. The combination of an MIC5014/ 5015 and a power FET also provides an elegant solution to power relay drive.
12V
Simple DC-DC Converter (Figure 11) The simplest application for the MIC5014 is as a basic one-chip DC-DC converter. As the output (Gate) pin has a relatively high impedance, the output voltage shown will vary significantly with applied load.
5V
10F MIC5014 1 2 3 V+ Input Source NC NC NC 8 7 6 VOUT = 12V
10F MIC5014 1 Control Input
ON OFF
4 Gnd
8 7 6 IRF540 Guardian Electric 1725-1C-12D
Gate 5
V+ Input Source
NC NC NC
2 3
4 Gnd
Gate 5
Figure 11. DC - DC Converter
Figure 9: Relay Driver
MIC5014/5015
8
June 2005
MIC5014/5015 High Side Driver With Load Protection (Figure 12) Although the MIC5014/15 devices are reverse battery protected, the load and power FET are not, in a typical high side configuration. In the event of a reverse battery condition, the internal body diode of the power FET will be forward biased. This allows the reversed supply access to the load.
Micrel, Inc. The addition of a Schottky diode between the supply and the FET eliminates this problem. The MBR2035CT was chosen as it can withstand 20A continuous and 150A peak, and should survive the rigors of an automotive environment. The two diodes are paralleled to reduce switch loss (forward voltage drop).
12V
10F MIC5014 1 Control Input
ON OFF
MBR2035CT 8 7 6 IRF540
V+ Input Source
NC NC NC
2 3
4 Gnd
Gate 5
Figure 12: High Side Driver WIth Load Protection
Push-Pull Driver With No Cross-Conduction (Figure 13) As the turn-off time of the MIC5014/15 devices is much faster than the turn-on time, a simple push-pull driver with no cross conduction can be made using one MIC5014 and one MIC5015. The same control signal is applied to both inputs; the MIC5014 turns on with the positive signal, and the MIC5015 turns on when it swings low. This scheme works with no additional components as the relative time difference between the rise and fall times of the MIC5014 is large. However, this does mean that there is
10F
considerable deadtime (time when neither driver is turned on). If this circuit is used to drive an inductive load, catch diodes must be used on each half to provide an alternate path for the kickback current that will flow during this deadtime. This circuit is also a simple half H-bridge which can be driven with a PWM signal on the input for SMPS or motor drive applications in which high switching frequencies are not desired.
12V
MIC5014 1 2 3 V+ Input Source NC NC NC 8 7 6 IRFZ40
4 Gnd Control Input
Gate 5
12V VOUT MIC5015 1 2 3 V+ Input NC NC 8 7 6 IRFZ40
Source 4 Gnd
NC Gate 5
Figure 13: Push-Pull Driver June 2005 9
MIC5014/5015
Load
MIC5014/5015
Micrel, Inc.
Package Information
PIN 1 DIMENSIONS: INCH (MM)
0.380 (9.65) 0.370 (9.40)
0.135 (3.43) 0.125 (3.18)
0.255 (6.48) 0.245 (6.22) 0.300 (7.62)
0.013 (0.330) 0.010 (0.254) 0.018 (0.57) 0.100 (2.54) 0.130 (3.30) 0.0375 (0.952) 0.380 (9.65) 0.320 (8.13)
8-Pin Plastic DIP (N)
0.026 (0.65) MAX)
PIN 1
0.157 (3.99) 0.150 (3.81)
DIMENSIONS: INCHES (MM)
0.050 (1.27) TYP
0.020 (0.51) 0.013 (0.33) 0.0098 (0.249) 0.0040 (0.102) 0-8 SEATING PLANE 45 0.010 (0.25) 0.007 (0.18)
0.064 (1.63) 0.045 (1.14)
0.197 (5.0) 0.189 (4.8)
0.050 (1.27) 0.016 (0.40) 0.244 (6.20) 0.228 (5.79)
8-Pin SOP (M)
MIC5014/5015
10
June 2005
MIC5014/5015
Micrel, Inc.
June 2005
11
MIC5014/5015
MIC5014/5015
Micrel, Inc.
MICREL INC.
TEL
2180 FORTUNE DRIVE
FAX
SAN JOSE, CA 95131 USA
WEB
+ 1 (408) 944-0800
+ 1 (408) 474-1000
http://www.micrel.com
This information furnished by Micrel in this data sheet is believed to be accurate and reliable. However no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 1997 Micrel Incorporated
MIC5014/5015
12
June 2005

▲Up To Search▲

Price & Availability of MIC501405

	To Download MIC501405 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .